|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
SiT8102 1 to 200 MHz High Performance Oscillator Features * High frequency stability * 10 PPM, 15 PPM, 20 PPM * 25 PPM, 50 PPM, 100 PPM * Extremely low RMS phase jitter (random) * 0.5 ps (typical) * Wide frequency range * 1 to 200 MHz * Operating voltage * 1.8, 2.5, 2.8V or 3.3 V * 2.25 V to 3.63 V (contact SiTime) * Operating temperature range * Industrial, -40 to 85 C * Extended Commercial, -20 to 70 C * Commercial, 0 to 70 C * Small footprint * 2.5 x 2.0 x 0.85 mm * 3.2 x 2.5 x 0.85 mm * 5.0 x 3.2 x 0.85 mm * 7.0 x 5.0 x 0.85 mm * All packages are Pb-free and ROHs compliant * High drive option: 30pF load (contact factory) Benefits * No crystal or capacitors required * Eliminates crystal qualification time * Ultra-reliable start up and greater immunity from interference * 50% + board saving space * More cost effective than quartz oscillators, quartz crystals and clock ICs. * Completely quartz-free Applications * * * * * * * * * * * Communications and Networking Applications Consumer Electronics Applications Automotive Applications Industrial Applications Gigabit Ethernet 10 Gigabit Ethernet Fiber Channel Ethernet SATA/SAS USB 2.0 PCI-Express Block Diagram VDD OUT Pinout ST/OE M EM S R eson ator H igh P erform ance S ynthesizer 1 4 VDD GND 2 3 OUT S T/O E GND Pin Description Pin No. Name 1 2 3 4 ST/OE GND OUT VDD Pin Description Standby/ Output Enable Connect to Ground 1 to 200 MHz Programmed Clock output Connect to 1.8V / 2.5V / 2.8V / 3.3V Pin1 Pin #1 Functionality OE H or Open; specified frequency output L: output is high impedance ST H or Open; specified frequency output L: output is low level (weak pull down) oscillation stops SiTime Corporation Rev. 1.08 990 Almanor Avenue, Suite 200 Sunnyvale, CA 94085 (408) 328-4400 www.sitime.com Revised December 08, 2008 SiT8102 Description The SiT8102 is the next generation of the SiT8002 programmable oscillator with lower phase noise, lower jitter, and a higher frequency range. SiTime oscillators are the smallest, high-performance programmable oscillator available and are suitable for use in high speed serial communications, consumer, portable, industrial, automotive and computation. This oscillator is packaged in standard low-cost plastic and chip-scale IC packages. System reliability is also increased with the SiT8102 by eliminating the quartz crystal and improved immunity to the environmental effects of vibration, shock, strain, and humidity. To order samples, go to www.sitime.com and click on Request Sample" link. Absolute Maximum Ratings Attempted operation outside the absolute maximum ratings of the part may cause permanent damage to the part. Actual performance of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings. Absolute Maximum Table Parameter Storage Temperature VDD Electrostatic Discharge Theta JA ( with copper plane on VDD and GND) Theta JC (with PCB traces of 0.010 inch to all pins) Soldering Temperature (follow standard Pb free soldering guidelines) Number of Program Writes Program Retention over -40 to 125 C, Process, VDD (0 to 3.65V) Min. -65 -0.5 - - - - - - Max. 150 +3.65 6000 75 24 260 1 1,000+ Unit C V V C/W C/W C NA years Operating Conditions Parameter Supply Voltages, VDD[1] Min. 2.97 2.25 2.52 1.7 Extended Commercial OperatingTemperature Industrial Operating Temperature Maximum Load Capacitance[2] -20 -40 - Typ. 3.3 2.5 2.8 1.8 - - - Max. 3.63 2.75 3.08 1.9 70 85 15 Unit V V V V C C pF Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Temperature Cycle Solderability Moisture Sensibility Level Condition/Test Method MIL-STD-883F, Method 2002 MIL-STD-883F, Method 2007 JESD22, Method A104 MIL-STD-883F, Method 2003 MSL1 @ 260C Notes: 1. The 2.5V device can operate from 2.25V to 3.63V with higher output drive, however, the data sheet specifications cannot be guaranteed. Please contact factory for this option. 2. The output driver strength can be programmed to drive up to 30pF load. Please contact factory for this option. Page 2 of 7 SiT8102 DC Electrical Specifications @VDD = 3.3V 10%, -40 to 85C Parameter Output Voltage High Output Voltage Low Input Voltage High Input Voltage Low Operating Current Standby Current Power Up Time Condition IOH = -9 mA IOL = 9 mA Pin 1 Pin 1 Output frequency = 30 MHz, 15 pF load Output frequency = 125 MHz, 15 pF load Output is weakly pulled down, ST = GND Time from minimum power supply voltage Min. 90 - 70 - - - - - Typ. - - - - - - 30 - Max. - 10 - 30 26 34 50 10 Unit %Vdd %Vdd %Vdd %Vdd mA mA A ms @VDD = 2.5V 10% or VDD = 2.8V 10%, -40 to 85C Parameter Output Voltage High Output Voltage Low Input Voltage High Input Voltage Low Operating Current Standby Current Power Up Time Condition IOH = -7 mA IOL = 7mA Pin 1 Pin 1 Output frequency = 30 MHz, 15 pF load Output frequency = 125 MHz, 15 pF load Output is weakly pulled down, ST = GND Time from minimum power supply voltage Min. 90 70 - - - - - Typ. - - - - - - 30 - Max. - 10 - 30 26 31 50 10 Unit %Vdd %Vdd %Vdd %Vdd mA mA A ms @VDD = 1.8V 5%, -40 to 85C Parameter Output Voltage High Output Voltage Low Input Voltage High Input Voltage Low Operating Current Standby Current Power Up Time Condition IOH = -5 mA IOL = 5 mA Pin 1 Pin 1 Output frequency = 30 MHz, 15 pF load Output frequency = 125 MHz, 15 pF load Output is weakly pulled down, ST = GND Time from minimum power supply voltage Min. 90 70 - - - - - Typ. - - - - - - 30 - Max. - 10 - 30 26 31 50 10 Unit %Vdd %Vdd %Vdd %Vdd mA mA A ms Page 3 of 7 SiT8102 AC Electrical Specifications @VDD = 3.3V 10%, -40 to 85C Parameter Clock Output Frequency Frequency Stability Inclusive of initial tolerance, operating temp., rated power supply voltage change, load change 0 to 70C -20 to 70C -40 to 85C Condition Min. 1 -10 -15 -20 -25 -50 -100 Aging Clock Output Duty Cycle Clock Output Rise Time Clock Output Fall Time RMS Period Jitter RMS Phase Jitter (Random) First year @ 25 C Output frequency= 1 to 125 MHz Output frequency= 125 to 200 MHz 15 pF Load, 20% to 80% VDD 15 pF Load, 80% to 20% VDD Output frequency = 75 MHz Output frequency = 125 MHz Output frequency = 75 MHz (900 kHz to 7.5 MHz) Output frequency = 106.25 MHz (637kHz to 10 MHz) Output frequency = 125 MHz (1.875 to 20 MHz) Typ. - - - - Max. 200 +10 +15 +20 +25 +50 +100 Unit MHz PPM PPM PPM PPM PPM PPM PPM % % ns ns ps ps ps ps ps - 45 40 - - - - - - - - - - 1.0 1.0 2.6 2.4 0.81 1.64 0.38 1 55 60 1.5 1.5 4 3.6 - - - @VDD = 2.5V 10% or VDD = 2.8V 10%, -40 to 85C Parameter Clock Output Frequency Frequency Stability Inclusive of initial tolerance, operating temp., rated power supply voltage change, load change 0 to 70C -20 to 70C -40 to 85C Condition Min. 1 -10 -15 -20 -25 -50 -100 Aging Clock Output Duty Cycle Clock Output Rise Time Clock Output Fall Time RMS Period Jitter RMS Phase Jitter (Random) First year @ 25 C Output frequency= 1MHz to 125MHz Output frequency= 125MHz to 200MHz 15 pF Load, 20% to 80% VDD 15 pF Load, 80% to 20% VDD Output frequency = 75 MHz Output frequency = 125 MHz Output frequency = 75 MHz (900 kHz to 7.5 MHz) Output frequency = 106.25 MHz (637kHz to 10 MHz) Output frequency = 125 MHz (1.875 to 20 MHz) Typ. - - - - Max. 200 +10 +15 +20 +25 +50 +100 Unit MHz PPM PPM PPM PPM PPM PPM PPM % % ns ns ps ps ps ps ps - 45 40 - - - - - - - - - - 1.0 1.0 3 2.8 0.87 1.7 0.41 1 55 60 1.5 1.5 6 5 - - - Page 4 of 7 SiT8102 @VDD = 1.8V 5%, -40 to 85C Parameter Clock Output Frequency Frequency Stability Inclusive of initial tolerance, operating temp., rated power supply voltage change, load change 0 to 70C -20 to 70C -40 to 85C Condition Min. 1 -15 -20 -25 -50 -100 Aging Clock Output Duty Cycle Clock Output Rise Time Clock Output Fall Time RMS Period Jitter First year @ 25 C Output frequency= 1 MHz to 75 MHz Output frequency= 75 MHz to 200 MHz 15 pF Load, 20% to 80% VDD 15 pF Load, 80% to 20% VDD Output frequency = 75 MHz Output frequency = 125 MHz RMS Phase Jitter (Random) Output frequency = 75 MHz (900 kHz to 7.5 MHz) Output frequency = 106.25 MHz (637kHz to 10 MHz) Output frequency = 125 MHz (1.875 to 20 MHz) Typ. - - - Max. 200 +15 +20 +25 +50 +100 Unit MHz PPM PPM PPM PPM PPM PPM % % ns ns ps ps ps ps ps - 45 40 - - - - - - - - - - 1.0 1.0 7.3 7.1 0.85 1.72 1.06 1 55 60 1.5 1.5 14 14 - - - Ordering Information SiT8102A C - 13 - 25E - 123.12345T Part Fam ily "SiT 8102" Revision Letter "A" is the silicon revision Tem perature Range "N " C om m ercial 0 to 70C "C " Extended C om m e rcial -20 to 70C "I" Industria l -40 to 85C Packaging: "T" for Tape & Reel Blank for B ulk Frequency 1.00000 to 200.00000 M Hz Feature Pin "E" for O utput Enable "S" for Standby Voltage Supply "18" for 1.8 V +/- 5% "25" for 2.5 V +/- 10% "28" for 2.8 V +/- 10% "33" for 3.3 V +/- 10% Frequency Stability Package Size "1" "2" "3" "4" 2.5 x 2.0 m m 3.2 x 2.5 m m 5.0 x 3.2 m m 7.0 x 5.0 m m "F" for + /- 10 ppm "H" for +/- 15 ppm "1" for +/- 20 ppm "2" for +/- 25 ppm "3" for +/- 50 ppm "4" for +/- 100 ppm Temperature Range FrequencyStability 10 PPM 15 PPM 20 PPM 25PPM 50 PPM N = 0 to 70C VDD = 2.5 or 2.8 or 3.3 V All VDDs NA C = -20 to 70C NA I = -40 to 85C VDD = 2.5 or 2.8 or 3.3 V VDD = 2.5 or 2.8 or 3.3 V All VDDs Page 5 of 7 SiT8102 Package Information [3] Dimension (mm) 2.5 x 2.0 x 0.85mm 2.50.10 1.0 1.9 Land Pattern (recommended) (mm)[4] 2.00.10 1.1 0.5 1.5 0.8 1.1 3.2 x 2.5 x 0.85mm 3.20.15 2.1 2.2 2.50.15 0.9 0.7 1.9 0.9 1.4 5.0 x 3.2 x 0.85mm 5.00.15 3.20.15 2.39 2.54 0.8 1.1 2.2 1.2 1.5 Page 6 of 7 1.6 1.2 1.0 SiT8102 Package Information (continued)[3] Dimension (mm) 7.0 x 5.0 x 0.85mm Land Pattern (recommended) (mm)[4] 0.850.15 Do not Connect the center pad or Connect it to Device's GND Notes: 3. xxxx top marking denotes manufacturing lot number. 4. A capacitor of value 0.1F between VDD and GND is recommended. (c) SiTime Corporation 2008. The information contained herein is subject to change at any time without notice. SiTime assumes no responsibility or liability for any loss, damage or defect of a Product which is caused in whole or in part by (i) use of any circuitry other than circuitry embodied in a SiTime product, (ii) misuse or abuse including static discharge, neglect or accident, (iii) unauthorized modification or repairs which have been soldered or altered during assembly and are not capable of being tested by SiTime under its normal test conditions, or (iv) improper installation, storage, handling, warehousing or transportation, or (v) being subjected to unusual physical, thermal, or electrical stress. Disclaimer: SiTime makes no warranty of any kind, express or implied, with regard to this material, and specifically disclaims any and all express or implied warranties, either in fact or by operation of law, statutory or otherwise, including the implied warranties of merchantability and fitness for use or a particular purpose, and any implied warranty arising from course of dealing or usage of trade, as well as any common-law duties relating to accuracy or lack of negligence, with respect to this material, any SiTime product and any product documentation. Products sold by SiTime are not suitable or intended to be used in a life support application or component, to operate nuclear facilities, or in other mission critical applications where human life may be involved or at stake. All sales are made conditioned upon compliance with the critical uses policy set forth below. CRITICAL USE EXCLUSION POLICY BUYER AGREES NOT TO USE SITIME'S PRODUCTS FOR ANY APPLICATION OR IN ANY COMPONENTS USED IN LIFE SUPPORT DEVICES OR TO OPERATE NUCLEAR FACILITIES OR FOR USE IN OTHER MISSION-CRITICAL APPLICATIONS OR COMPONENTS WHERE HUMAN LIFE OR PROPERTY MAY BE AT STAKE. SiTime owns all rights, title and interest to the intellectual property related to SiTime's products, including any software, firmware, copyright, patent, or trademark. The sale of SiTime products does not convey or imply any license under patent or other rights. SiTime retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by SiTime. Unless otherwise agreed to in writing by SiTime, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. Page 7 of 7 |
Price & Availability of SIT8102AC-13-33E-800000 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |